NEWS CENTER


Common building glass on the market

Different architectural parts will use different architectural glass. Especially in the application of external windows, because of the transparent lighting and heat resistance of the glass to keep warm. In different occasions, glass with different functions is also needed. Tempered glass, insulating glass, heat-reflective glass and other glass with various functions came into being. Today, SINOY editor will take you to learn about several commonly used architectural glass.   1. Tempered glass Tempered glass is made by heating float glass to near the softening point in a tempering furnace, and then rapidly and uniformly cooling it, forming uniform compressive stress on its surface, increasing its mechanical strength, and effectively improving the wind pressure and impact resistance of the glass Performance, improve the thermal shock resistance of glass. Tempered glass is widely used in places that require relatively high mechanical strength and safety. Such as glass doors and windows, building curtain walls, glass furniture, indoor partitions, elevators, furniture, etc.   Performance characteristics of tempered glass 1) Safety: When broken, it splits into small obtuse-angle particles similar to honeycombs, which hardly cause serious harm to the human body. When ordinary glass is broken, it is a sharp large piece of fragments, which is easy to cause serious harm to the human body. 2) High strength: 4-5 times stronger than ordinary glass of the same thickness. 3) Stable heat resistance: With good thermal stability, the temperature that can withstand is about 3 times that of ordinary glass of the same thickness, and it can withstand temperature changes of 200°C. Therefore, it can play a short-term fire prevention effect in the event of a fire. 4) Large interference: 3-4 times larger than ordinary glass of the same thickness. When tempered glass is loaded, its maximum tensile stress is not located on the surface of the glass like ordinary glass, but at the center of the tempered glass plate.   2 Laminated glass Laminated glass is a composite glass made by sandwiching a tough polyvinyl butyral film (PVB) between two or more pieces of glass, which is made through high temperature and high pressure. Because the toughness of the PVB film is very good, when the laminated glass is violently impacted and broken by an external force, the film layer will absorb a large amount of punching skills and make it attenuate rapidly. Because the laminated glass is difficult to be broken down, even if the laminated glass is broken, the glass The fragments basically adhere to the film, keeping the fragments on the entire laminated glass from falling off, so it becomes the real safety glass. Laminated glass made of transparent PVB film, its appearance and installation method are basically the same as ordinary glass, and it is durable. It is widely used in building lighting roofs, canopies, high-end curtain walls, doors and windows, shop windows, furniture, elevators, etc.   Performance characteristics of laminated glass 1) Safety: The laminated glass installed on the building is subject to any external impact, even if the glass is broken, it can be kept in the original frame completely, and has a certain function of sheltering from wind and rain. 2) The noise-reducing PVB film has an obstructive effect on sound waves, thereby reducing noise and reducing noise interference at work or home. 3) Anti-ultraviolet rays: Great blocking effect on ultraviolet rays in sunlight (up to 99% or more) and avoid ultraviolet radiation. Therefore, it can protect valuable indoor homes or artworks from fading caused by ultraviolet rays. 4) Bulletproof and explosion-proof: the use of multilayer laminated glass can produce various levels of bulletproof and explosion-proof glass. 5) Security: Because glass cutters cannot be used to effectively cut the installed laminated glass, and the use of other tools to penetrate the laminated glass takes a long time and the sound is loud, it is difficult and easy to enter the room by cutting or breaking the laminated glass. It is found that it has a strong resistance to vicious destruction, theft and violence. 6) Protection against hurricanes and earthquakes: Due to the high toughness and strong adhesion of laminated glass, even if the laminated glass is broken, the fragments will still remain in place. It is more suitable for use in hurricane and earthquake areas.     3 Insulating glass Insulating glass is a glass product made of two or more pieces of glass separated by a certain width of space with an aluminum frame filled with molecular sieve adsorbent, bonded and sealed with butyl glue, and then sealed with silicone glue or structural glue. Has good sound insulation, heat insulation, heat preservation, anti-condensation and other effects. Insulating glass is widely used in various building curtain walls, doors and windows, indoor partitions or freezers, etc. Thickness of insulating gl

10-13

2020

The difference between painted glass and colored mirror

How to distinguish between painted glass and colored mirror? Is it different? First of all, let’s take a look at the difference between the following two pictures   Presumably, you should not be able to distinguish the differences between these two types of glass and mirrors. Now there is a editor from SINOY to take you to understand the similarities and differences between painted glass and colored mirrors.   Colored mirrors refer to various colored mirrors made of high-quality colored float glass as the original instead of ordinary float transparent glass. Color mirrors are divided into two categories: color aluminum mirrors and color silver mirrors. Namely color aluminized glass mirror and color silvered glass mirror. The colors sold in the market are blue, green, gray, brown, gold, black, pink, etc.   Painted glass is also called back-painted glass in the industry, divided into flat painted glass and frosted painted glass. Spray paint on the back of the glass and bake it in an oven at 30-45 degrees for 8-12 hours. In many places where baking varnished glass is made, natural drying is generally used, but the adhesion of naturally dried paint is relatively small, and in a humid environment Easy to fall off. According to different production methods, baking varnished glass is generally divided into: paint sprayed glass and colored glazed glass. In colored glazed glass, it is divided into low temperature colored glazed glass and high temperature colored glazed glass. Paint-sprayed glass has bright colors when it is first used, mostly in single color or partial color registration with multiple layers of saturated colors. It is often used indoors. When outdoors, it will peel off the paint after being exposed to wind, rain and sun.   Similarities between the two The common point of the two is that they are all glass deep-processing products. The color mirror has good finish and the coating is relatively stable; the painted glass looks like a color mirror from the front, but the paint is prone to bubbles and trachoma cannot be installed in the air   Can you now distinguish between the two pictures above which is the lacquered glass and which is the color mirror?   The above is the report brought by SINOY editor Angus.

10-13

2020

The difference between silver mirror, grey mirror and bronze mirror

Mirrors are inorganic non-metallic materials that are widely used and have a wide range of applications. They can be used in construction, daily use, art, instrumentation and other fields, and the types are very rich. In addition to the commonly used silver mirrors and aluminum mirrors, there are also bronze mirrors, grey mirrors and no bronze mirrors. Now let the editor of SINOY take you to understand the difference between silver mirror, grey mirror and bronze mirror. Silver mirror Silver mirrors are made by adopting modern advanced mirror-making technology, choosing special-grade float glass as the original film, and performing a series of processes such as sensitization, silver plating, copper plating, and protective paint. It is characterized by pure imaging, high reflectivity, good color reproduction, bright and natural images, and durable even in humid environments. It is a replacement product for aluminum mirrors, and its scope of use extends far beyond aluminum mirror products. Widely used in furniture, handicrafts, decoration, bathroom mirrors, makeup mirrors, optical mirrors, and car rearview mirrors.   Grey Mirror Gray mirror is a widely used decorative mirror. In general, it is divided into color mirror ranks. The basic process of its production is to plate a layer of silver powder on the gray glass, and then paint one or more layers of high corrosion resistance environmentally friendly paint, and through a series of beautification and cutting processes.   Bronze mirror The bronze mirror is a silver mirror made of citrine or brown glass. The color of the bronze mirror looks like golden . In many cases, the bronze mirror designed as an ornament will have some special geometric shapes, which have a very good decorative effect. . So it is widely used in furniture, handicrafts, decoration, etc.   Therefore, they do not have a major difference in materials on the market, but there are certain differences in manufacturing processes.   The above is the editor of SINOY editor Angus

10-13

2020

Bathroom mirror installation skills

Mirror installation methods can be roughly divided into five types: screw fixation, stud fixation, bonding fixation, supporting pressure fixation and bonding support fixation. Each approach has its own characteristics and scope of application. According to the size of the mirror, the method of arrangement, the place of use and other factors, choose one of them to use alone or a combination of several installation methods. 1. Primary treatment When building walls or pillars, wooden bricks should be embedded in the wall. The width of the horizontal and the mirror surface is equal, and the firm direction is equal to the height of the mirror. Large-area mirror installation should also be buried in the horizontal and firm directions every 500mm. The walls should be plastered. According to the different parts used, hot asphalt or linoleum should be applied to the plastering surface, or the linoleum can be sandwiched between the wooden lining board and the glass. The main purpose of these practices is to prevent moisture from causing the wood The liner is deformed to prevent the coating from falling off due to moisture and the mirror surface loses its luster. 2. Standing ribs The wall reinforcement is a small wooden square of 40*40mm or 50*50mm, nailed to the wooden brick with iron nails. The installation of small mirrors is mostly two-way vertical bars, and the installation of large mirrors can be one-way vertical bars, and the positions of horizontal and solid wall bars are consistent with the wooden bricks. The vertical ribs are required to be horizontal and straight to facilitate the fixing of the liner and the mirror. Therefore, the horizontal and vertical lines must be hung when erecting the ribs. Before installation, check whether the moisture-proof layer is completed. After the erecting ribs are nailed, use a long stick to check the flatness. 3. Nail liner The lining board is a 15mm thick wooden board or a 5mm thick plywood, which is connected to the wall reinforcement with small iron nails, and the nail heads are submerged in the board. The size of the liner can be larger than the spacing of the vertical ribs, which can reduce the cutting process and increase the construction speed. It is required that the surface of the lining board has no warpage or peeling phenomenon, and the surface is smooth and clean. The gap between the board and the board should be at the vertical rib. 4. Mirror installation The construction of mirror installation includes: mirror cutting, mirror drilling and mirror fixing. 5. Mirror cutting When installing a certain size mirror, cut a part of the large mirror surface, and cut it on a table or on a flat ground, and plywood or carpet on it. Place the large mirror surface on the table or the ground, measure the size according to the design requirements, rely on the ruler board, use a glass knife to cut from the beginning to the end, move the mirror cutting line to the edge of the table, and use the ruler board at one end Hold down, hold the other end, and quickly move down the board. 6. Mirror drilling If you choose to drill the mirror with screws, the hole position is generally at the corner of the mirror. First put the mirror on the table or the ground, measure the size according to the drilling position, mark the drilling point with a plastic pen, or drill a small hole with a glass drill, and then water the area to be drilled, the diameter of the drill bit Should be larger than the screw diameter. When drilling holes, water continuously on the mirror surface until it is drilled through. Pay attention to reduce the force when you want to drill through. 7. Mirror fixed When the mirror is installed, the fixing methods usually include screw fixation, stud fixation, adhesive fixation, support pressure fixation and adhesive support fixation. At this point, the installation of the bathroom mirror is complete.   Written by Olivia Wang,from Sinoy Mirror Inc

10-12

2020

Problems that need to be paid attention to before the installation of bathroom mirrors

Everyone is very familiar with the mirrors in the bathroom, and with the development of the decoration industry, we are more and more aware of the importance of the mirror. It can not only provide us with freshening and dressing, but also make the entire bathroom "larger" , Our vision will be exposed to different feelings. Therefore, for the installation of bathroom mirrors, we must also master the coup. Before installing the bathroom mirror: 1. When installing the mirror headlight, pay attention to prevent glare. It is recommended to install a lampshade or choose a lamp with a frosted glass surface. 2. Mirror height: Generally, it is better to keep the center of the mirror 160-165 cm above the ground. 3. The mirror in the bathroom should be framed. If it is not framed, it needs to be sealed and waterproof. 4. When installing, be careful not to damage the wall, especially hang a mirror on the ceramic tile wall, try to punch holes in the material joints. 5. In addition to installing ordinary mirrors, it is recommended to install a stretchable magnifying glass above the washbasin. 6. When taking a bath, the mirror in the bathroom is blurred by the steam. You can apply soap on the mirror surface and wipe it with a dry cloth to prevent the mirror surface from blurring. 7. The dirt on the mirror can be wiped with a soft cloth or gauze dipped in some kerosene or wax, but do not wipe with a wet cloth, otherwise the mirror surface will be blurred and the glass will be easily corroded.   Written by Olivia Wang,from Sinoy Mirror Inc

10-12

2020

Is there any difference between silver mirror and ordinary mirror?

The silver mirror is coated with silver nitrate, which is not easy to oxidize and rust. Ordinary mirrors can use mercury nitrate or mercury sulfate to replace silver nitrate to save costs, but the stability of mercury is not as good as silver, and it is easy to oxidize and rust. Silver mirrors are much clearer than ordinary mirrors, and the geometric angle of the object light source is more standardized. Ordinary mirrors have low reflectivity and their reflection performance is about 70%. They are easily distorted in shape and color, and have short lifespan and poor corrosion resistance. They have been completely eliminated in European and American countries. However, ordinary mirrors are easy to produce on a large scale, and the cost of raw materials is relatively low. In addition, in terms of quality, it is generally mercury, but the quality and production process are quite different. High-quality ones should be waterproof and will not be distorted after a long period of time. Distorted and deformed after a long period of time.   Written by Olivia Wang,from Sinoy Mirror Inc

10-12

2020

Cleaning and maintenance of bathroom mirrors

In a bathroom filled with moisture, the mirror will inevitably be contaminated with moisture, and it will deteriorate and appear black spots over time. When maintaining your bathroom cabinets, bathtubs and other large bathroom items, don't forget to maintain your mirrors. Let Yinjing Sanitary Ware tell you the secret of making mirrors as clean as new. Mirrors are afraid of moisture, because mirror glass is generally cut before use. Water vapor will easily enter the mirror surface from the side cut by the glass knife, corrode the mirror surface, and produce mildew and rust spots. Therefore, the expert advice of Yinjing Sanitary Ware: After buying the mirror, first apply a layer of lacquer on the side of the mirror and also on the back. In addition, pay attention to the following points during daily maintenance: Usually the mirror should be placed in a dry place, not just hanging on the wall, and not near the washbasin. Do not touch the mirror with wet hands, and do not wipe the mirror with a damp cloth, so as to avoid increasing the pouring of moisture and making the optical layer of the mirror black. The mirror should not be in contact with salt, grease and acidic substances, which are easy to corrode the mirror surface. Wipe the mirror surface with a soft dry cloth or cotton to prevent the mirror surface from being rubbed; or use a soft cloth or emery cloth, dipped in some kerosene or wax to wipe; you can also wipe the mirror and frame with a rag dipped in milk to make it clear and bright . In addition, wipe with oil-absorbent tissue, the effect is also good. The frame should be wiped with a soft cotton cloth or cotton, worsted silk back to prevent the frame from rusting. Before bathing, you can apply soap to the mirror surface and wipe it with a dry cloth. A layer of soap liquid film is formed on the mirror surface to prevent blurring of the mirror surface. You can also use astringent lotion or detergent. Dip an appropriate amount of detergent with a dry cloth and apply it to the mirror surface and spread evenly. The active ingredients contained in the detergent can effectively prevent water vapor from condensing on the mirror surface, and can effectively prevent fog.   Written by Olivia Wang,from Sinoy Mirror Inc

10-12

2020

The choice of smart home needs attention

The difficulty of implementing a smart home is indeed not too difficult, but it is not as simple as we thought. Because many families now have so many smart home products more or less, it is precisely because of this that many people feel that their homes already have smart homes. No, it can only mean that your understanding of smart home is not comprehensive enough. So how to choose a more suitable smart home from the perspective of individuals and families? Clarify individual needs Before you buy smart home products, you must clarify what your needs are and what personalized services you need. Because each family has different requirements for smart life, the purchase of smart homes is naturally different. The functions of the smart home can be arbitrarily combined to meet the needs of different consumers for smart life. In addition to the necessary functions, such as home security systems, alarm systems, smart lighting systems, smart mirror system,etc., we can also install smart home products according to our special needs, such as home entertainment systems, background music systems, etc., which allow us to Enjoy more entertainment at home. Is the function integrated Smart home integration is the use of integrated wiring technology, network communication technology, security technology, automatic control technology, audio and video technology to integrate equipment related to home life. A centralized and unified control method is adopted for home equipment, so the core should be a communication protocol, a system platform for an intelligent sweeping robot, and a solution, equivalent to a computer operating system. The corresponding specific products, such as security products, monitoring products, light control products, multimedia products,smart mirror etc., can be integrated into this system. Through the communication protocol of the system, the various subsystems can be connected to each other and exchange information. Mutual control. However, many products on the market now only have a simple sub-system equipment product, which is also advertised as a smart home, which is actually incorrect. This requires consumers to make a detailed analysis with the merchant before purchasing, and the compatibility of the product It must be good. choose energy-saving and environmentally friendly products Energy saving and environmental protection have become the subject words, and promoting energy saving has become a consumer trend and industrial trend. All walks of life are also advocating "energy saving" and "environmental protection". As a smart home manufacturer, providing users with products that are both easy to use and energy-saving cannot be ignored. The smart home control system based on computer technology and automation technology, the energy-saving and environmental protection function is the most prominent in the lighting energy saving. The intelligent sweeping robot can be realized through various timing event management, induction control functions, and automatic detection of light brightness by brightness sensors. Lighting energy saving, etc.  Whether it has remote control function Remote control refers to the realization of various remote control through remote control, timing controller, centralized controller or telephone, mobile phone, computer, etc. Smart home is equivalent to a family's smart control center, integrating home appliance control, home security and monitoring, home information terminals, and home digital entertainment. Therefore, please check whether you can access the smart terminal through the Internet and operate the experience when purchasing. product and brand choice When choosing a product, the main consideration is the quality and appearance of the product. In addition to smart home products that can bring us smart enjoyment, in fact, good appearance crafts can also bring beautiful visual enjoyment to our family. Some smart home products focus on the functions of the product and ignore the visual enjoyment of the appearance. In fact, this is also a point that consumers cannot ignore when buying products. When choosing a brand, you must follow the principle of "shop around". Choosing an excellent smart home brand manufacturer is a good way to avoid risks. Because a big brand manufacturer can guarantee the quality of the product and the technology can also be guaranteed. Therefore, when choosing a smart home, you must choose a brand with good reputation and high reputation as much as possible. This allows you to buy with confidence and use with confidence. Of course, when you choose an agent, it is best to follow this principle. Is the product after-sales service considerate For each manufacturer, the after-sales service of the product is an important factor in the development of the enterprise. Consumers pay great attention to the quality of after-sales service when buying large consumer products. Especially when buying smart home products, this is even more i

09-01

2020